| Filler | Minerals |
| Mixing Ratio | |
| (A:B) by weight | 5:6 |
| (A:B) by volume | 1:1 |
| Color | Grey |
| Density [g/cm3] | 1.33 |
| at room temperature | |
| Viscosity | |
| at 23C Brookfield | |
| Component A (mPas) | 100,000 thix |
| Component B (mPas) | 130,000 thix |
| Mixture (mPas) | 100,000 thix |
| Pot life | Water absorption (%) | 0.1 | |
| In 100 gm preparation at 23C / 73F (min) | 60 | DIN 53495, 24h at RT | |
| Gelling Time | Coefficient of elongation (1/K) 60xE-6 | ||
| In 100 gm preparation at 23C / 73F (min) | 90 | Acc to DIN 16946 | |
| Curing Time |
Shore Hardness D | 80 | |
| At room temp(hours) | 24 | DIN 53505 | |
| At 80C / 176F (min) | 60 | ||
| Maximum reaction temp |
Indentation hardness (Mpa) | 80 | |
| In 100gm preparation (c) | 80 | DIN 53456 | |
| Firmness to touch (hr)
|
4.5 | Temperature solidity (Mpa) | 5.0 |
| Tensile/shear strength 1-2 Mpa | DIN 53286, sand-blasted Joint part material: al/al thickness: 1.6 mm |
||
| Functional Stability (hr)
|
8 | Temperature Stability © | 200 |
| Tensile/shear strength > 10 Mpa | |||
| Tensile/shear
strength DIN 58283, EN 1465 |
Specific volume | 5.2xE15 | |
| VDE 0303, part 3 | |||
| Joint part material: al/al (Mpa) | 21 | ||
| Sand-blasted Joint part thickness: 1.6mm After 24 hr at room temperature |
|||
| DIN 54451 | Surface resistance R | 2.3xE12 | |
| Joint part material: al/al (Mpa) | 26 | VDE 0303, part 3 | |
| Sand-blasted Joint part thickness: 6mm After 72 hr at room temperature |
|||
|
Floating roller peel |
3.5 | Breakdown voltage E (kV/mm) | 21 |
| Resistance (N/mm) |
VDE 0303, part 4 | ||
| Din 53289 acc to EN 1464 Joint part material: st/st sand-blasted |
|||
| Tensile strength (Mpa) | 38 | Creep resistance CTI | 4.1 |
| DIN 53455 | VDE 0303, part 1, IEC 112 | ||
| Elongation at tear (%)
|
1.4 | Chemical stability | Very Good |
| DIN 53455 | |||
| Storage life |
Modulus of elasticity (Mpa) |
3200 | |
| DIN 53457 |
Storage: Store in original containers at room temperature and off the floor. Prevent exposure to cold or elevated temperature.
Handling: Wear suitable protective clothing to prevent skin and eye contact. Prevent contact with vapors by providing adequate ventilation or personal NIOSH approved respirators. Isolate from epoxy resin and work areas to limit exposure to other personnel, tools or equipment.
Spills, disposal: Only properly trained and equipped personnel should be involved with clean up or spills. Small spills can be cleaned up with absorbent rags or sand. Dispose or any wastes or empty containers in accordance of all applicable federal, state and local regulations.
Please read the MSDS for complete information regarding the handling of this product .For further information contact the BCI technical sales department at (847) 488-0123.
Warranty: All Recommendations, estimates and technical data contained herein are based on tests we believe to be reliable and correct. Bonding Concepts Inc warrants its product to be free of manufacturing defects and that at the time and place of shipment, our material will meet current published physical properties when applied with BCI directions in accordance with BCI standards. Bonding Concepts Inc liability is limited to replacement of material found to be defective. As BCI has no control over the use to which others may put its products, it is recommended that the product be tested to determine if suitable for a specific application and / or our information is valid in a particular circumstance. Responsibility remains with the buyer to the design application and proper installation of each product. Nothing contained herein shall be construed to be a recommendation to use or as a license to operate under or to manage any existing patents.